Mon-Fri: 7AM-8PM, Sat: 8AM-6PM, Sun: 9AM-5PM Licensed & Insured [email protected] Serving Dana, NC

Holmes Garage Door Garage Door Roller Replacement in Dana, NC

Worn steel or plastic rollers swapped for quiet, sealed nylon rollers. Typical cost $150-$350.

Need Holmes Garage Door garage door roller replacement in Dana, NC? We diagnose the problem, give you a price before any work starts, and finish most jobs in a single visit. Worn steel or plastic rollers swapped for quiet, sealed nylon rollers. We work on Holmes Garage Door garage doors of every age, from older models to current lines, and carry or can source compatible parts.

Signs you need Holmes Garage Door garage door roller replacement

  • Grinding, squealing or rumbling as the door moves
  • The door shakes or jerks in the track
  • Cracked, chipped or wobbly rollers
  • Rollers that no longer spin freely

Why this happens

  • Worn-out bearings in steel rollers
  • Cracked builder-grade plastic rollers
  • Rust or dust packed into the bearings

Before the technician arrives

  • Watch the rollers while the door moves. They should roll, not slide.
  • Look for cracked plastic wheels or wobbling stems.
  • Leave the bottom rollers to a technician. They sit in brackets that hold cable tension.

Still stuck? Our free symptom checker and troubleshooting wizard walk you through it step by step.

How we handle Holmes Garage Door garage door roller replacement

  1. Inspect every roller, hinge and track section
  2. Replace rollers one hinge at a time, with sealed nylon rollers for a quieter door
  3. Replace the bottom rollers safely with tension controlled
  4. Lubricate hinges and bearings
  5. Test for smooth, quiet travel

Typical Holmes Garage Door garage door roller replacement prices

$150-$350Typical range, parts & labor
about 1 hourTypical time on site

What moves the price:

  • Door size and weight (single or double, steel or wood)
  • Which parts need replacing and whether they are in stock
  • Spring type and cycle rating
  • Emergency or after-hours timing

These are typical U.S. ranges, not a quote. You get an exact price for your door before any work starts. For a quick estimate, try the repair cost calculator.

Other Holmes Garage Door services

Serving Dana, NC and nearby towns

Humid air in North Carolina rusts cables, roller bearings and hinges, which makes the door noisy and heavy and eventually makes the opener strain.

Close to the coast, salt air speeds up corrosion. Galvanized or coated springs, nylon rollers and stainless hardware hold up better than bare steel.

Technicians serve all of Dana (ZIP code 28724), plus East Flat Rock (4.3 mi), Fruitland (4.8 mi), Edneyville (4.9 mi) and Hendersonville (4.9 mi). Call (833) 435-8883 to book a visit in Dana.

Holmes Garage Door Garage Door Roller Replacement: frequently asked questions

How much does Holmes Garage Door garage door roller replacement cost in Dana, NC?

Holmes Garage Door Garage Door Roller Replacement typically costs $150-$350 including parts and labor, and usually takes about 1 hour. The exact price depends on your door and the parts it needs, and you get it before any work starts. Call (833) 435-8883 for a quote.

Can you do Holmes Garage Door garage door roller replacement the same day?

Often, yes. When a technician is available we can usually come the same day, and common parts are carried on the truck. Doors that won't close or have a broken spring are treated as priority calls, and emergency service is available.

Is Holmes Garage Door garage door roller replacement covered by a warranty?

Our work comes with a 90-day labor warranty on repairs. New parts and doors also carry the manufacturer's warranty, and Holmes Garage Door warranty terms vary by product and age. Ask for the warranty details in writing with your quote.

Are your technicians licensed and insured?

Our technicians are insured, and where North Carolina or Dana requires a contractor license for garage door work, the job is done under that license. You're welcome to ask for proof when you book.

Should I repair or replace my garage door?

A good rule of thumb: if the repair costs more than about 50% of a replacement, or the garage door is near the end of its life, replace it. A garage door typically lasts 15 to 30 years. If several panels are damaged, the door is rusted through or rotted, or parts are discontinued, replacing it is often better value. Springs are the exception: a broken spring is always replaced, never repaired. Our free repair vs. replace calculator can help you compare.

More services

Popular Garage Door Services in Dana, NC

Haas Door Commercial Garage Door Repair

Repairs for commercial sectional, overhead and service doors.

Typical $250-$1,000

Sommer Opener Circuit Board Replacement

Sommer openers, made in Germany, put the motor on a carriage that travels along the rail instead of hanging from the ceiling, so servicing them is a little different from a conventional opener.

Typical $175-$400

Northwest Door Weather Seal Replacement

New bottom seals, threshold seals and perimeter stops to keep out water and drafts.

Typical $100-$300

Linear Garage Door Opener Installation

Linear openers and remotes are now part of Nice North America. Linear's MegaCode remotes are common on older openers and gate systems.

Typical $350-$800

Holmes Garage Door Garage Door Installation

New steel, insulated, wood-look and carriage-style doors, measured and professionally installed.

Typical $1,200-$4,500

Wayne Dalton Garage Door Panel Replacement

Wayne Dalton is part of the Overhead Door Corporation. Many Wayne Dalton doors use the TorqueMaster spring system, with the springs sealed inside the torsion tube, so spring work needs TorqueMaster parts and a different procedure.

Typical $300-$900

Overhead Door Rolling Fire Door Inspection & Drop Testing

Annual drop testing and inspection of rolling fire doors.

Typical $150-$500

Holmes Garage Door Weather Seal Replacement

New bottom seals, threshold seals and perimeter stops to keep out water and drafts.

Typical $100-$300

Genie Opener Circuit Board Replacement

Genie is the residential opener brand of the Overhead Door Corporation. Genie openers use Intellicode rolling-code remotes, Genie is one of the few brands still offering screw-drive openers, and newer models connect to the Aladdin Connect app.

Typical $175-$400

Wayne Dalton Torsion Spring Replacement

Wayne Dalton is part of the Overhead Door Corporation. Many Wayne Dalton doors use the TorqueMaster spring system, with the springs sealed inside the torsion tube, so spring work needs TorqueMaster parts and a different procedure.

Typical $200-$450

Windsor Door Weather Seal Replacement

New bottom seals, threshold seals and perimeter stops to keep out water and drafts.

Typical $100-$300

Overhead Door Extension Spring Replacement

Overhead Door traces its roots to C.G. Johnson, who invented the upward-acting garage door in 1921. The company builds residential and commercial doors and openers.

Typical $150-$350

Garage door stuck, noisy or broken?

Talk to a garage door technician in Dana, NC now. Tell us what the door is doing and we'll give you a price and an arrival window.

Call NowFree Quote